Our Products
6000 FXP
3000 FXP
3000 XP
2500 Manual/Electric
1500 Manual/Electric
1000 XP
Tri-Pod Kit
Man-Hole EXT. Kit
Force Gauge
Tugger Talkers
Rope & Accessories
Uni-Grips
Our Company
About Us
Contact
Site Map
More Info
How-To
Privacy
PORTA~PULL 1000XP
Everything you need to make your next job a lot easier!
Our “NEW”1000XP is a complete WIRE PULLING SYSTEM and even includes a FOOT SWITCH!
- FIBER OPTIC
- VIDEO CABLE
- TELE-COMMUNICATIONS
- ELECTRICAL CABLE
- POOL & LIGHTING CIRCUITS
Introducing the all new “Apprentice Mate” 1000XP. Capable of extending up to 11 feet with 1 stick of 3/4" Rigid conduit, the 1000XP Cable Puller is great for technicians needing a simple, yet effective method of pulling in runs from practically anywhere!
In fact, chances are, if you can see it...you can pull it! The Universal head design rotates a full 360 degrees to quickly accommodate Up-Down & Side pulls from single gang boxes, load centers, disconnects, wiring hubs, etc.
And with 1000 lbs. of pulling force, the 1000XP Cable Puller will put the POWER of 3 men to work for you!
In fact, chances are, if you can see it...you can pull it! The Universal head design rotates a full 360 degrees to quickly accommodate Up-Down & Side pulls from single gang boxes, load centers, disconnects, wiring hubs, etc.
And with 1000 lbs. of pulling force, the 1000XP Cable Puller will put the POWER of 3 men to work for you!
- 1HP single speed motor and gearbox.
- Extends over 11’ with 3/4" rigid conduit.
- Remote foot switch included.
- Will even pull from a single gang box.
- 12” & 24” Rigid extensions included.
- Powder coated industrial finish.
- Right angle sheave for operator safety.
- 1-year warranty.
- Length: Compact-30” Extended-11 Feet+
- Width: 7”
- Height: 4”
- Weight: 20 pounds.
- Power: 1 HP (746 watts) 120 volts/8 amps.
- Pulling force: 600 lbs Continuous.
- 1000 lbs Momentary.
- Pulling speed: 50 feet per minute.
- Recommended rope size: 1/4 or 5/16”
SET UP INSTRUCTIONS
Rotate the head as necessary to perform the type of pull you will be doing. Typical up pull is shown in photo. Once adjustment is made, secure head in position by tightening right angle sheave.
When ready to start pulling cable, use only three wraps of rope on the capstan at first. Using too many wraps will reduce your ability to control the rope on the capstan. Use the right angle sheave to position yourself so you are not in line with the high tension rope in case it, the cable or the connector breaks.
Turn on the puller by depressing the foot pedal switch and gradually apply a tailing force to the free end of the rope. If the tailing force becomes uncomfortably high, turn off the puller and add another wrap. If the rope starts to climb or double on itself, ease up on the tailing force to allow it to settle down to the base diameter. If it is continually climbing or doubling, turn off the puller and remove a wrap.
Turn on the puller by depressing the foot pedal switch and gradually apply a tailing force to the free end of the rope. If the tailing force becomes uncomfortably high, turn off the puller and add another wrap. If the rope starts to climb or double on itself, ease up on the tailing force to allow it to settle down to the base diameter. If it is continually climbing or doubling, turn off the puller and remove a wrap.
Loosen locking screw to adjust head assembly. Place head next to conduit connector. Use a nylon tie wrap to secure head to conduit connector if necessary.
Bring pull rope over front roller and down to capstan. Apply three (3) turns of rope to capstan and finish by bringing pull rope up to and thru right angle sheave. You can now begin your pull.
Click here to purchase the 1000XP
Cable and Wire Pulling System Accessories
CABLE TUGGERS/CABLE PULLERS
MADE IN THE USA